course | Vibration Analysis and Condition Monitoring
Vibration Analysis and Condition Monitoring course designed for professionals in UAE. Learn, apply, and get certified in vibration analysis condition
MEC-1466 | Vibration Analysis and Condition Monitoring
Course Sector : Mechanical Engineering
| Duration | Date from | Date to | Course Venue | Course fees | Book a course |
|---|---|---|---|---|---|
| 5 Days | 13/12/2026 | 17/12/2026 | Doha | $4,250 | Book now |
| 5 Days | 05/04/2027 | 09/04/2027 | Abu Dhabi | $4,250 | Book now |
| 5 Days | 14/06/2027 | 18/06/2027 | Barcelona | $4,950 | Book now |
| 5 Days | 30/08/2027 | 03/09/2027 | Dubai | $4,250 | Book now |
Course Introduction
An introduction to performing vibration analysis within a condition monitoring program. Various techniques used to diagnose machinery condition are reviewed, including time waveforms, spectral analysis, phase measurements, and amplitude measurement methods. Applies sensor fundamentals to vibration analysis, including an overview of sensor strengths and weaknesses in applications.
Common machinery malfunctions are discussed, including basic guidelines for the best detection tools for each machinery problem, and key signs to be aware of. Malfunctions and common pitfalls are demonstrated, and real-world vibration analysis case histories are shared.
Course objective
- Participants should learn how to select appropriate sensors and techniques for diagnosing typical machinery malfunctions.
- Participants will be learned to read vibration signatures and evaluate machinery condition from vibration data.
- Participants will understand how to isolate the affected machinery components, recognize various common problems, and make recommendations for continued efficient operation or scheduled repairs.
Course audience
- Automotive Engineer
- Boiler Engineer
- Ceramics Engineer
- Equipment Engineer
- High-Pressure Engineer
- Marine Engineer
- Mechanical Design Engineer
- Mechanical Engineer
- Naval Architect
- Pipeline Engineer
- Power Engineer
- Rotating Equipment Engineer
- Senior Mechanical Engineer
- Turbine Engineer
- Validation Engineer
Course Outline | 01 DAY ONE
Module (01) Condition Monitoring Introduction
- Maintenance strategy and types
- Source of vibration
- Infra thermography technique overview
- Oil Analysis Technique Overview
Course Outline | 02 DAY TWO
Module (02) principles of vibration analysis
- Vibration amplitude
- Vibration displacement
- Vibration velocity
- Vibration acceleration
- Data Acquisition Technique
- Measurement point’s identification
- Phase concept and measurement
Module (03) vibration measurement sensors
- Proximity report theory and operation
- Velocity transducer theory and operation
- Accelerometer theory and operation
- Sensor Selection Criteria
- Sensors fixation methods and effect
Course Outline | 03 DAY THREE
Module (04) Vibration analysis fundamentals
- Converting from time waveform spectrum.
- Free Vibration Concept
- Forced vibration
- Resonance phenomena identification and problem solving
- Critical Speed Identification
- Non, sub, and synchronous frequencies
Module (05) Rotor unbalance fault detection and solving
- Unbalanced defect reasons
- Unbalance detection using vibration analysis
- Detection using spectrum and timewaveform
- Detection using phase analysis
- Detection using orbit analysis
- Unbalance Correction Method
- Unbalanced impact on machinery health
Course Outline | 04 DAY FOUR
Module (06) misalignment defect detection and solving
- Misalignment sources
- Misalignment detection using vibration analysis
- Detection using spectrum analysis
- Detection using timewave form analysis
- Detection using phase analysis
- Detection using orbit analysis
- Misalignment solving problem
- Alignment using dial gauges
- Alignment using a laser alignment device
- Belt alignment
Module (07) Bearing defects detection and solving
- Bearing failure sources
- Bearings failure stages
- Bearing failure detection
- Bearing failure effect on machinery health
- Proper bearing installation methods
Course Outline | 05 DAY FIVE
Module (08) Other Common Machinery Defects
- Rotor Eccentricity Detection
- Belt defect detection
- Bent Shaft Detection
- Looseness defect detection
- Internal looseness
- External looseness
BOOST’s Professional Attendance Certificate “BPAC”
BPAC is always given to the delegates after completing the training course,and depends on their attendance of the program at a rate of no less than 80%,besides their active participation and engagement during the program sessions.
Since 2001, we’ve been at the forefront of professional training in the Middle East — shaping the future of learning and development one success story at a time. With a vision rooted in innovation and excellence, we help individuals, teams, and organizations reach their highest potential through integrated, future-ready training solutions. Our comprehensive programs combine global best practices with local insights, empowering people to grow, lead, and make a lasting impact in their industries.
🔗 Quick Links
Sister Companies to Boost Consulting and Training
most trending
And Recommended Training Courses
We believe in progress for everyone.
We helped more than 10,000 clients over 20 countries on 4 continents in boosting their knowledge, skills, and careers.
Boost Training And Consulting All Copyrights Reserved 2026