course | Steam Power Plant Layout System & Equipment Operation
Advance your career with Steam Power Plant Layout System & Equipment Operation. Hands‑on learning in UAE covering steam power plant layout system and more
MEC-1478 | Steam Power Plant Layout System & Equipment Operation
Course Sector : Mechanical Engineering
| Duration | Date from | Date to | Course Venue | Course fees | Book a course |
|---|---|---|---|---|---|
| 5 Days | 21/09/2026 | 25/09/2026 | Dubai | $4,250 | Book now |
| 5 Days | 28/12/2026 | 01/01/2027 | Dubai | $4,250 | Book now |
| 5 Days | 15/03/2027 | 19/03/2027 | Abu Dhabi | $4,250 | Book now |
| 5 Days | 05/07/2027 | 09/07/2027 | Baku | $4,950 | Book now |
Course Introduction
This course is devoted to presenting the different systems in a steam power plant and its components. Main steam and auxiliary systems necessary for operation are discussed in detail. The details and sequence of starting up and operating these systems and their components are also discussed. The proper understanding of functions and the operation of different systems will be beneficial to the overall performance of the plant and will thus reduce emergency trips and hazardous situations.
Course objective
- Major and Auxiliary components in a steam power plant.
- Function and operation of different equipment’s in the plant.
- Layout and circuits of different systems in the plant.
- Safety and trip functions in the plant.
- Start up of auxiliary systems.
- Start up of main steam systems.
- Start up of main and auxiliary components.
Course audience
- Automotive Engineer
- Boiler Engineer
- Ceramics Engineer
- Equipment Engineer
- High-Pressure Engineer
- Marine Engineer
- Mechanical Design Engineer
- Mechanical Engineer
- Naval Architect
- Pipeline Engineer
- Power Engineer
- Rotating Equipment Engineer
- Senior Mechanical Engineer
- Turbine Engineer
- Validation Engineer
Course Outline | 01 DAY ONE
Module (01) Introduction and Common Auxiliary Systems
- Raw Water Supply Desalination & Demineralized Water System
- Instrument & Service Air System
- Closed Cooling Water System
- Auxiliary Steam System
Course Outline | 02 DAY TWO
Module (02) Fuel and Air Systems
- Fuel Gas System
- Igniter Header and Level Safety Shutoff Valves
- Main Fuel Gas Safety Shutoff Valve
- Light Oil System
- Function and Description
- Start up
- Heavy Oil System
- Fuel Oil Combustion System: Heavy Oil Day Tank
- Heavy Oil Day Tank Suction Heater
- Fuel Oil Burner Heaters
- Fuel Oil Burner Supply Pumps
- Fuel Oil Burner Pumps Suction Strainers
- Fuel Oil Safety Shutoff Valves
- Fuel Oil Control Valves
- BMS Control and Operations
- Safety Shutdown
- Air and Gas Circuit
- Fuel and Air Control System
- BMS Operational Overview
- Light Up (Cold Condition)
- Checklist
- Furnace Boiler Purge
- Fuel Leak Control Test
- First Burner Light Up
Module (03) Boiler Start-Up Systems and Procedure
- Boiler Descriptions
- Boiler Filling
- Boiler Feed Water System
- Drum, SH, and RH Protections
- Pressure Raise
- Boiler Load Increase
- Chemical Parameters
- Boiler Start-Up Curves
- Cold Start-Up Curve
- Warm Start-Up Curve
- Hot Start-Up Curve
Course Outline | 03 DAY THREE
Module (04) Turbine Start-Up Systems and Procedure
- Steam Turbine Description
- Turbine Auxiliary Circuits
- Turbine Oil System
- Lubrication oil system
- Electro-hydraulic control oil system
- Turbine control system
- “On-Off Control” Actuators
- “Proportional Control” Actuators
- Actuator Servo Valve
- Auto stop oil / Emergency trip oil
- Gland Sealing Steam System
- Turbine Bypass System
- Steam Turbine Start-Up Procedure
- Preparation For Rolling
- Start High-Pressure Fluid System
- Steam Rolling and Loading
- Turbine Start-Up Curves
- Cold start-up curve
- Hot start-up curve
- Turbine Start-Up Schedule
Course Outline | 04 DAY FOUR
Module (05) Condensate System
- Steam Surface Condenser
- Condenser Hotwell Level gauge
- Vacuum Breakers
- Condensate Pumps
- Condensate Pump Check Valve
- Condensate Storage Tank
- Condensate Transfer Pump
- Condensate Supply Pumps
- Condenser vacuum systems
- The Liquid Ring Pump
- Ejector System
- Gland Steam Condenser
- Low-Pressure Feedwater Heaters
- Deareator
Course Outline | 05 DAY FIVE
Module (06) Generator Start-Up Systems and Procedure
- Description 6.2 Auxiliary Circuits
- Service Gas System
- Generator Gland Seals (Hydrogen Seals)
- Air Side Seal Oil System
- Hydrogen Side Seal Oil System
- Seal Oil Backup
- Seal Oil Coolers
- Differential Pressure Regulator for AC Air-side Seal oil pump
- Closed Circuit Cooling Water System
- Stator-Coil Cooling Water System
- Generator Start-Up Sequence
- DRYING 6.5.2 Leakage Test
- Inspection of Phase
- Initial start
- Start Up
- Synchronization To The Line
BOOST’s Professional Attendance Certificate “BPAC”
BPAC is always given to the delegates after completing the training course,and depends on their attendance of the program at a rate of no less than 80%,besides their active participation and engagement during the program sessions.
Since 2001, we’ve been at the forefront of professional training in the Middle East — shaping the future of learning and development one success story at a time. With a vision rooted in innovation and excellence, we help individuals, teams, and organizations reach their highest potential through integrated, future-ready training solutions. Our comprehensive programs combine global best practices with local insights, empowering people to grow, lead, and make a lasting impact in their industries.
🔗 Quick Links
Sister Companies to Boost Consulting and Training
most trending
And Recommended Training Courses
We believe in progress for everyone.
We helped more than 10,000 clients over 20 countries on 4 continents in boosting their knowledge, skills, and careers.
Boost Training And Consulting All Copyrights Reserved 2026